What is the default username and password for Cisco switch? (2024)

What is the default cisco switch username and password?

Log in to the switch console. The default username and password is cisco. If you have configured a new username or password, enter those credentials instead.

(Video) How to configure username and password on CISCO switch/Router
(IT Funkaar)

What is the default password for cisco 9300 switch?

Enable the switch command to enter into the privilege mode. Log into the management port with default username cisco. The password for the same is the serial number of your switch chassis.

(Video) How to Reset a Cisco Switch to Default (with or without password)
(ITProTV)

What is the default password for cisco 2960 switch?

When prompted, enter the default password, cisco.

(Video) Cisco Switch Prompt for Username an Password Console Access
(Khosiab Hmoob)

What is default IP of cisco switch?

To access the switch by using the web-based interface, you must know the IP address the switch is using. The switch uses the factory default IP address of 192.168. 1.254 by default.

(Video) Password reset for Cisco catalyst 3560 switch
(Tech Made Easy)

What is the default username and password?

Default Router Username And Password List
Router BrandDefault Username
3BenQadmin
4D-Linkadmin
5Digicomadmin
6Linksysadmin
19 more rows
Aug 7, 2022

(Video) How to setup username and password on cisco router and switch
(Khmer Cisco Learning)

How do I find my cisco password?

Most routers and switches by Cisco have default passwords of admin or cisco, and default IP addresses of 192.168. 1.1 or 192.168. 1.254.

(Video) How To Reset the Password on a Cisco 9200 Series Switch
(LookingPoint, Inc.)

What is cisco Enable password?

To set a local password to control access to various privilege levels, use the enable password command in global configuration mode. Use the no form of this command to remove the password requirement.

(Video) How to Assign Console Password on CISCO Switch
(Vishesh Malik, Technical Guru)

How do I reset my cisco admin password?

From root access run the command 'passwd admin'. This should prompt to enter a new password for the admin access. Hey malford, From root access run the command 'passwd admin'.

(Video) Cisco Catalyst 9300, 9200, 3650, 3850, 2960X Switch Password Recovery / Reset How To
(The Tech Catalyst)

What is the default password for cisco phone?

Enter the password of the device in the Password field. The default password for the administrator is admin and for the user it is cisco. Note: If you forget the password, you can reset the phone adapter to factory defaults which in turn returns the device to the default login.

(Video) How to set console password with username on cisco router
(SYS ADMIN)

How do I reset my cisco 2960 to factory settings?

Reset a Cisco 2960 Switch to Factory Default Settings
  1. - Start by connecting your cisco switch via a console cable that will be also connected to the same console.
  2. Step 2.- Use the following commands: Router: en. Router#erase startup-config. Router# del flash:vlan.dat.
  3. - Reload your cisco switch to complete the restoration.

(Video) How To Reset Cisco Switch Password
(the fiX files)

How do I connect my cisco Catalyst 2960 switch?

Follow these steps:
  1. Connect the supplied RJ-45-to DB-9 adapter cable to the 9-pin serial port on the PC. Connect the other end of the cable to the console port on the switch.
  2. a. Configure the PC terminal emulation software for 9600 baud, 8 data bits, no parity, 1 stop bit, and no flow control.
  3. a.

(Video) How to set Username and Password on Cisco Routers - Login and Login Local
(T3SO Tutorials)

What is cisco Connect guest password?

The default username and password is cisco/cisco. If you have configured a new username or password, enter the credentials instead. Click Login.

What is the default username and password for Cisco switch? (2024)

How do I connect to a cisco switch?

How to configure Cisco switch?
  1. Step 1: Use an external emulator such as Telnet or a PuTTY to login to the switch.
  2. Switch# configure terminal. ...
  3. Step 2: Provide a hostname for the switch to function in a particular network environment.
  4. Switch(config)#hostname switch.

How do you set a cisco switch to default?

Resetting the Cisco IP switch to factory defaults
  1. Erase the existing configuration: write erase.
  2. Reload the switch software: reload. The system reboots and enters the configuration wizard. ...
  3. In the configuration wizard, enter the basic switch settings: ...
  4. When prompted, enter the user name and password to log in to the switch.

How do I connect to a cisco Managed switch?

How to Configure Cisco Switch: A Step-by-Step Guide with Commands
  1. Getting Started with Cisco Switch Commands.
  2. Connect the Switch to PuTTY.
  3. Enter Privileged EXEC Mode and Set a Hostname for the Switch.
  4. Assign a Password to the Switch.
  5. Configure Telnet and Console Access Passwords.
  6. Configure IP Addresses With Telnet Access.
Apr 21, 2022

What is login command in cisco?

Login command is used in VTY for password that is specified to be checked at login. If you do not use login command you will not able to use the specified password for the vty to login. Login can also be used with login local. In which you can config a username and password on the router to be auth.

How do I log into cisco?

Cisco router login:
  1. Make sure you're connected to your network.
  2. Open a browser, and go to 192.168. 15.1.
  3. Enter the username and password.
  4. Default login credentials.
  5. Next Up: Speed up your Wi-Fi connection.
Nov 19, 2020

How can I recover my password?

You've made Windows password recovery very easy for yourself.
  1. On the login screen, click on Reset passwords.
  2. Plug in your USB key (or floppy disk). Click Next.
  3. Type in your new password and a password hint. Click on Next.
  4. Done!
Jun 2, 2022

What is the username and password for cisco dpc3825?

Enter the following default settings to access the modem settings and select Login: Username: cusadmin. Password:password(or your current WiFi password)

What is cisco Enable password?

To set a local password to control access to various privilege levels, use the enable password command in global configuration mode. Use the no form of this command to remove the password requirement.

What is the default username or password for cisco sg350?

The default username is cisco, and the default password is cisco. Usernames and passwords are both case sensitive.

How do I reset my cisco switch password?

Technique #7
  1. You must be on the console.
  2. Reboot the device.
  3. When you see the password prompt, press Enter (null password for 30 seconds).
  4. Type Enable.
  5. When you see the password prompt press Enter (null password for 30 seconds).
  6. Change the password.

How do I reset my cisco DPC3825 router password?

How to Reset your Cisco DPC3825 Modem
  1. Locate the Reset button the back of the modem.
  2. Press and hold the Reset button for 10 seconds.
  3. After 10 seconds, release the button. The modem should restart and the lights will flash.
  4. Once the modem is finished restarting and is online the settings will be back to default.

How do I log into my cisco router?

Cisco router login:
  1. Make sure you're connected to your network.
  2. Open a browser, and go to 192.168. 15.1.
  3. Enter the username and password.
  4. Default login credentials.
  5. Next Up: Speed up your Wi-Fi connection.
Nov 19, 2020

How do I log into my cisco modem?

Introduction
  1. Open a web browser such as Internet Explorer.
  2. Go to the Address bar and enter the IP Address of your router then press Enter. For example, 192.168. ...
  3. A new window prompts for a User name and Password. Type admin for User name and Password, since admin is the default user name password, and then click OK.

References

You might also like
Popular posts
Latest Posts
Article information

Author: Van Hayes

Last Updated: 02/06/2024

Views: 5897

Rating: 4.6 / 5 (66 voted)

Reviews: 81% of readers found this page helpful

Author information

Name: Van Hayes

Birthday: 1994-06-07

Address: 2004 Kling Rapid, New Destiny, MT 64658-2367

Phone: +512425013758

Job: National Farming Director

Hobby: Reading, Polo, Genealogy, amateur radio, Scouting, Stand-up comedy, Cryptography

Introduction: My name is Van Hayes, I am a thankful, friendly, smiling, calm, powerful, fine, enthusiastic person who loves writing and wants to share my knowledge and understanding with you.